Comments on: SolidWorks Video Tip: Layout Sketches and Planes

By: ok

ok — Wed, 28 Apr 2010 20:21:36 +0000

Lutilisation de vos dépenses flexibles expliquent travesti (FSA) pour la thérapie de massageest une travesti autre façon valable pour se maintenir avec votre habitude de massage. Les comptes flexibles de dépenses sont établis parvotre travesti fournisseur d'assurance maladie pour gérer de l'extérieur de coûts de votre médecin standard visite chaque an. travesti Ces sont considéré être généralement ‹ un-remboursé les dépenses médicales, travesti et les fournisseurs d'assurance maladie différente ont des indications différentes sur ce qu'ils accepteront. travesti Dans la plupart des cas vous pouvez réclamer la
thérapie de massage travesti comme un un-remboursé la dépense médicale si le c'est pour traiter une blessure, un traumatisme, travesti ou une maladie spécifique. Le massage pour le soulagement de tension,la détente, ou maintenant juste la travesti bonne santé est d'ordinaire pas remboursable. Si vous devez masser travesti pour la thérapie physique ou soulagement de tension, profitez de n'importe quel de ces stratégies si ces thérapie de massageest travesti devenue une partie de votre travesti mode de vie sain. mode de vie sain.

By: nbenitezg

nbenitezg — Sat, 26 Sep 2009 21:32:11 +0000

thanks
muchas gracias

By: weewilly

weewilly — Wed, 10 Dec 2008 20:04:45 +0000

Hi Brian,
Yes, I did find out before your response that it is possible but not exactly in the way that I was trying to do it. There is another reduction parameter that must coincide along with the reduction size you wish to attain. It is in that little window box right up above the size you type in. I'm having a small problem with the computer right now or I would pull up the program. From memory told to me by someone else that when you use the scale tool and the property manager shows up you must choose the centroid paratmer to reduce the scale of the whole part. Hope that answers it. Glad to share it with you and as soon as I can straighten out my problem I will try what I just relayed to you. Take care.

By: Brian

Brian — Wed, 10 Dec 2008 18:28:44 +0000

Rich,

Maybe I am misunderstanding, but you can enter a value less than 1 in the Scale command and your part will get smaller.

Brian

By: weewilly

weewilly — Wed, 03 Dec 2008 16:45:01 +0000

Hi Again Ricky,

I was recently asked about scaling parts inside of SolidWorks. I did some reading on it but admittedly I do not understand a lot of it in the Help Menu. I tried scaling up to enlarge things but could not figure out how to reduce things. Or is that even possible? Sure would appreciate some direction on this one if you want an idea. In advance I thank you.

Richie.

By: weewilly

weewilly — Wed, 03 Dec 2008 13:53:11 +0000

Hi Ricky,
Wow sure am learning a lot from my fellow blog squad members. You guys are showing me what is possible when I haven't even come across it yet in my imagination when I use SolidWorks. I think the question might come to mind about getting to the nuts and bolts of the question. “What can't SolidWorks do.” Since it seems to be able to do everything in a very safe and regimented way, I'm not sure what else could be added. Seeing what all of you can do with this program keeps me constantly amused and inspired at the same time. Bye for now. Richie.

By: Rod_Uding

Rod_Uding — Wed, 03 Dec 2008 09:41:54 +0000

No, I will go check it out right now!

By: Ricky Jordan

Ricky Jordan — Wed, 03 Dec 2008 04:03:52 +0000

I'm glad you found it useful. I'm always looking for more content ideas so if you have suggestions, send them my way!

Ricky

By: Ricky Jordan

Ricky Jordan — Wed, 03 Dec 2008 03:17:28 +0000

Rod,

Have you tried the new link I posted last night? It is the same one you might have seen posted via Twitter yesterday. Please let me know if this one performs better than the original one in the post. I think the disclaimer is a GREAT idea. My goal though is in the next few days develop a better video set which loads faster. If I am unsuccessful in this, I will post the disclaimer.

Thanks for all your feedback.

Ricky

By: Rod_Uding

Rod_Uding — Wed, 03 Dec 2008 00:30:24 +0000

Ricky, maybe if you just post a disclaimer to let us know it will take a while to download the video and suggest we get some liquid refreshment and a snack while it is downloading. That would work for me .